GHIANT Lexan aerosola krāsa Fluo Deep Red Nr 1010, 150 ml

Ready-to-use, quick-drying, and fuel-resistant lightweight spray paint in fluorescent deep red, specially developed for painting polycarbonate RC car bodies.

The solvent etches the surface to bond permanently with the material, offering up to 15 grams less weight on a 1/10 scale race body compared to pre-painted or water-based options for a lower center of gravity.

For best results, apply in very light coats from a distance of approximately 15 to 20 cm at temperatures above 15°C, and back the dried paint with white RC Car Colour to achieve the desired fluorescent effect.

• Delivered in a 150ml can.

Fluorescent deep red spray paint for polycarbonate RC car bodies, 150 ml

Hazard statements (H codes)

• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.

Precautionary statements (P codes)

• P210: Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: IF eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

Supplemental hazard information

• EUH066: Repeated exposure may cause skin dryness or cracking.

In the box

• 1× 150 ml spray paint

Before painting, remove dirt particles, cut out the body and sand the cut edges. Mask areas that are not to be painted with masking film or tape; make sure surfaces are dry and free of dust.

Many bodies have a transparent protective foil on the outside. Do not remove it until the paint has dried.

Paint dark colours before light colours to prevent the dark colours from showing through.

Shake the can vigorously for approx. 2 min. before use, until the mixing ball rattles. Spray from approx. 20–30 cm using even cross movements.

Covering capacity varies slightly by colour. Apply light coats to avoid bleeding; the final result takes 2–3 coats. Wait approx. 5 min. between coats rather than applying one heavy coat. Let the paint dry for 5 minutes before removing the masking film and applying the next coat.

After use, turn the can upside down and spray for 2 s until the nozzle is empty.

Fluorescent colours appear not to cover as well as normal colours. Apply only very light coats at temperatures above 15 °C, spraying from a distance of +/-15/20 cm.

Let the fluorescent colour dry for 30 min., then back it with white RC Car Colour to obtain the fluorescent effect.

RC Car Colours Fluo Deep Red is a paint for Lexan car bodies. The solvent etches the body surface so the paint bonds permanently with the plastic. The paint remains elastic, even in a strong crash, and does not chip or scratch.

Highlights

• Remains elastic
• Bonds permanently with the body
• Fuel-resistant

Hazard statements (H codes)

• H222: Extremely flammable aerosol.
• H229: Pressurized container: may burst if heated.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.

Precautionary statements (P codes)

• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P251: Do not pierce or burn, even after use.
• P305 / P351 / P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P337 / P313: If eye irritation persists: Get medical advice/attention.
• P403 / P233: Store in a well-ventilated place. Keep container tightly closed.
• P410 / P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

Supplemental hazard information

• EUH066: Repeated contact may cause dry or cracked skin.

In the box

• 1× Lexan paint Fluo Deep Red, 150 ml

Notes

Remove any protective foil on the outside of the body only after painting; the body can be cut out beforehand.

Clean the body thoroughly with dish soap or brake cleaner and shake the can vigorously for about 2 min.

• General application note: Spray the paint from a distance of 20–30 cm. When using multiple colours, start with the darkest, as dark colours can otherwise show through light ones.

Apply several thin coats instead of one thick coat and wait about 5 min between sprays. Wait at least 5 min before removing the protective film or masking film of the design.

After use, turn the can upside down and spray for about 2 s to empty the nozzle.

• Note for fluorescent colours: The paint is less opaque than standard colours; apply several fine coats from a distance of 15–20 cm at an ambient temperature of at least 15 °C.

Wait about 30 min and back the fluorescent colour with white to increase the luminosity.

• Brand: Ghiant